运用留意事项
1、定完雕琢方位后，有必要把X、Y、Z轴工件坐标全部归为“0”。
2、调好雕琢速度和主轴电机转速，以防雕琢时呈现速度过快、转速过慢而断刀。
3、主动对刀时，留意对刀块有必要跟雕琢机铝台面绝缘。
4、雕琢时，如果对第一刀没把握或怕犯错时，能够把进刀速度调慢，觉得雕琢正常时再把速度调回正常;也能够在空程中模仿雕琢，看是否正常。
5、如果长时刻不运用木匠雕琢机，应守时每周加油空转，最好为每个星期，以确保传动系统的灵活性。
6、要求木匠雕琢机接连运行时刻为10小时/天以下;确保冷却水的清洁及水泵的正常作业，绝不可使水冷主轴电机呈现缺水现象，守时更换冷却水，以防止水温过高，循环水尽量多，能够换大容量水箱。
7、每次运用木匠雕琢机结束，要留意整理，有必要将平台及传动系统上的粉尘整理洁净;守时对传动系统X、Y、Z三轴的光滑加油。
8、操作人员最好在操作木匠雕琢机时要佩带防尘口罩和防护眼镜，以防止在加工时发生的粉尘等侵入人体，形成不适。
9、木匠雕琢机日常保护办法要在木匠雕琢机加上必定的防尘除尘设备，挑选除尘设备配套运用。
木匠雕琢机【输出原点】的终究意图是把刀具途径精确的定位到板材上。
原点是木匠雕琢机刀具运动的一个参照点。假设把刀具途径的原点界说为X、Y的左下角、Z方向界说为0点，，那么刀具途径上的其它点就以这个点为参照点来断定相对方位。木匠雕琢机刀具在雕琢中就以这些点相对于原点的参数进行加工。
在进行雕琢时，首先要界说X、Y、Z三个方向的起刀点，起刀点与原点是一一对应的联系。起刀点的方位就是刀具途径加工文件的原点方位。起刀点的方位界说好了，那么这个刀具途径的原点就断定了。加工时刀具就以起刀点为参照点进行雕琢。
所以输出原点设置至关重要，设置错误板材就废了，购买机器后必定要和技能认真学习，等习气以后操作就没大问题了。
Use of attention
1, after the setting of the engraving position, the coordinates of the X, Y and Z axes must be all classified as "0".
2, adjust the speed of carving and spindle motor speed, in order to prevent the cutting speed is too fast, the speed is too slow and cut the knife.
3. When the knife is automatically opposed, the knife block must be insulated from the aluminum table of the engraving machine.
4, when carving, if the first knife is not grasped or afraid of making mistakes, it can slow down the feed speed and feel that when the carving is normal, it will return the speed to normal. It can also simulate carving in the empty space to see if it is normal.
5. If a carpenter engraving machine is not used for a long time, it is necessary to make regular weekly refueling, preferably every week, to ensure the flexibility of the transmission system.
6, woodworking engraving machine running for 10 hours / day; ensure the normal operation of cooling water cleaning and water, not the water-cooled motor there was a shortage of water, regular replacement of the cooling water, to prevent the water temperature is too high, the circulating water can change as much as possible, a large amount of water.
7, every time we use woodworking engraving machine, we must pay attention to cleaning. We must clean up the dust on the platform and transmission system, and regularly lubricate the transmission systems X, Y and Z three axes.
8, operators should wear respirators and goggles when operating woodworking engraving machines, so as to avoid dust and other intrusions during processing and cause discomfort.
9, the daily maintenance method of carpenter engraving machine should be added to a certain dustproof and dusting device in the woodworking engraving machine, and choose the supporting equipment for the use of the dust removal equipment.
The ultimate aim of the carpenters engraving machine is to locate the tool path accurately on the board.
The origin is a reference point for the tool movement of a woodworking engraving machine. If the origin of tool path is defined as X, Ys bottom left corner and Z direction are defined as 0 points, then other points on tool path take this point as the reference point to determine the relative position. Carpenter engraving tools are used to process these points with respect to the parameters of the origin.
In the process of carving, first we should define the three directions of X, Y and Z, and the relationship between the starting point and the original point is one by one. The position of the knife point is the origin of the tool path processing file. The position of the knife point is defined, then the origin of the tool path is determined. In processing, the cutter is carved with the point of reference as the reference point.
So setting the output point is very important. Setting up the wrong plate will be wasted. After buying the machine, we must learn hard with technology. After that, there will be no big problem if we use the habit.
